Tag Archives: shale shaker

Gn PRO Shale Shaker

Explore everywhere,The brand new generation shale shaker combines balanced and gressive elliptical motion, enabling operators to change motion “quickly” as drilling conditions change. Having a simple switch of the switch, the shale shaker changes in the balanced elliptical to the gressive elliptical motion with no need to suspend or shut lower procedures.

Operators can alter the kind of motion needed either to handle high volume orduce dryer clippings, as drilling conditions dictate. Using the shale shaker, nonproductive time lost to altering out shakers to satisfy drilling conditions is no more an problem.

Balanced elliptical motion handles high volume solids

Effective to find the best-hole sections with heavy, high volume solids, the balanced elliptical motion vides 7.5 Gs of pressure to rapidly move high volumes of solids over the screens. The motion increases conveyance rates and shaker fluid capacity while enabling the shaker to cess heavier solids.

Progressive elliptical duces dryer clippings

The gentler action of the gressive elliptical motion works well once the clippings volume is reduced, such as with lower sections, and operators desire a longer drying out here we are at the clippings. The G-pressure is reduced to six.5 Gs to optimize drilling fluid recovery and duce dryer clippings. The efficiency of the motion enables for greater processing rates while growing clippings dryness to reduce haul off costs.

Composite screens vide longer existence and greater screen area

The mud agitator is made to use the gn america high-capacity composite screens that vide a substantial rise in fluid capacity in addition to excellent potential to deal with blinding viding dryer solids discharge along with a bigger internet functional screen area.

Multiple shakers mix to multiply results

As much as four shale shakers could be pre-aligned in the factory and mounted on one skid to permit simpler rig moves, needing just one lift. Dual and trip models may use a typical possum belly and can include integral feeder slide gates to balance flow or divert it one shaker.

Welcome to visit our official website, we will be happy to serve you.

operate the cuttings dryer system after long time off status

If we operate the cuttings dryer system after long time off status, we need to inspect motor rotary unit on insulation. Use 500V Ω gauge, get resistance is not larger than 0.5MSZ, we can run the shaker

Notice: ① If the motor doesn’t run at all, we must shut off the power immediately to avoid motor broken
② After starting motor, to inspect, whether this is any problem. If there is any break off or uncommon noise. If two motors are not running in-phase we need to stop the motors and get rid of problems then turn it on again for operation
③ When motor is under cold status, should not be started 5 times continuously; when motor is turned off under hot status, the restart can not be over 3 times continuously
Shaker screen maintenance
① Before every shut off, the shaker should run without any medium for 5-10 minutes, at the same time, use clean water to flush screen clean
② Every time finish operation, the shaker frame and screen should be flushed by water (summer) or steam (winter), there should be not much sediment on shaker frame and shaker screen. Especially when the drilling mud has large viscosity and high density or screen is finer than 60 mesh. Otherwise, the particles and fine sand on screen will block screen hole, when we start shale shaker, it will decrease filtration result and lead drilling mud flow away, lose much unnecessary cost.
cuttings dryer maintenance
Electric control cabinet is explosion proof magnetic starter, the electric principle is as fig VI, if there is any trouble we must shut off the power, and repaired by electrician or specific person
Spare parts for GNPS752
No. Name Model Unit Qty Remark
l Vibration motor MVE2400/15D Set 1 1.0kW
2 Vibration motor MVE1100/15D Set 1 0.4kW
3 Shaker screen 750×900mm PC 2 40/20目
4 Tension wedge PC 4
5 Spring PC 4
6 Damping horizontal strip PC 4
7 Damping vertical strip PC 4
8 Enclosed files for GNPS752
9 GNPS752 Shale shaker user manual 1 set
10 GNPS752 Quality certificate on shale shaker 1 set
Resource Box :
The author of the article recommends,if need pls contact us

Gnsolidsamerica company produces high cost shale shaker

This section contains a summary of WARNINGS. The ZCQ Degasser has been designed to perform the stated functions safely.

All persons responsible for operation and maintenance of this equipment must read and understand all safety information in this manual prior to operating and/or maintaining the equipment. The safety warnings listed below are included in applicable procedures throughout this manual.

This section describes the recommended installation procedure for the ZCQ270/360 Vacuum Degasser. Instructions include site preparation, equipment leveling, feed

and discharge connections, and electrical connections.

Gnsolidsamerica.com is the owner of the article on shale shaker screen  and shale shaker , pls click gnsolidsamerica to know more info,pls visit us http://www.gnsolidsamerica.com/linear-motion-shale-shaker.html