Suck Dangerous Gas from Fluids-Vacuum Degasser

Leave a reply

GN Vacuum degasser is a special equipment for purifying drilling fluid. Vacuum degasser plays an important role in drilling fluid viscosity and stability of drilling fluids density. Even the drilling fluids does not contain harmful gases, it could work as a big mud agitator

Vacuum Degasser Working Principle:

Firstly, the vacuum pump suction is generated in the negative pressure zone sealed container, under negative pressure, the fluids will be sucked by the tube into the hollow shaft of the rotor, By the collision between drilling fluids and units, the dangerous gas within fluids will be pump to be discharged into the safety zone . the fluids will flow back to the mud tank. Therefore, the vacuum is able to complete separate the harmful gas and recovery the drilling fluids.

The feature of vacuum degasser

1 uses negative pressure degasser, reasonable design structure of science, to achieve effective gas-liquid separation, filter out impurities, ensure the exhaust pipe is always smooth;

2 using a belt drive, avoiding the complicated gear mechanism to ensure long working hours;

3 water ring vacuum pump(used on the decanter cenfuge) in the work process, always in isothermal state for flammable gas pumping, safe and reliable performance;

4 degassing efficiency is over 95% and maximum kick out the dangerous gas

GN Solids America degasser is a self-contained unit, which suck the fluids by itself. GN degasser is monitored by level sensor to protect over sunction of the fluids.

GN Solids America is the first API & ISO certified solids control supplier in China. We fabricates a full line of products for the solids control industry including shaker screens, mud cleaners, dryer shakers and closed loops system. GN is dedicated to remove impurities and recover reusable drilling fluid, transfer the recovered drilling fluid to and ultimately return it to our clients mud tank. Give us a call, GN will give you more option.

Air Compressor for GN Decanter Centrifuge Application.

Leave a reply

Air compressor is a very common unit in the drilling jobsite. Air compressor is widely used for the oil drilling site, water well drilling site, rock drilling site and mining drilling. Today, I am talking about the air compressor with our VFD (Variable Frequency Drive) control panel decanter centrifuge.

What is the GN VFD control panel decanter centrifuge?

Pressurized Stainless Steel Electrical VFD (ABB Brand) Control Box is by PLC smart control and touch screen, the advanced system is for high temperature environment and dangerous zone application. We have ATEX and IEC Ex Certified VFD control panel available for North America and European standard. GN VFD control panel is used in GNLW363BG, GNLW453, GNLW553 and GNLW363BD model. VFD control panel is able to control the feeding pump, main motor and back drive motor of centrifuge in order to achieve the flexible speed and meet for different jobsite requirement. Take VFD GNLW363BG as a example, typical bowl speed is between 0 and 3200 RPM and differential speed is between 0 and 40 RPM under the VFD control panel.

Why does GN decanter centrifuge require air compressor?

It is widely acknowledged that there is some dangerous gas in the drilling site. When we start the decanter centrifuge on the drilling site, hazardous gas may cause the explosion in the control cabinet. Therefore, we need expel all the dangerous gas prior to start the decanter centrifuge. Air compressor plays an important role in kicking off dangerous gas and providing a safe working place. GN decanter centrifuge installs the air pressure sensor to automatically control starter of decanter centrifuge. There is no doubt that air compress is a necessary tool for the GN decanter centrifuge.

GN Solids Control is a leading manufacturer of Solids Control Units and experts in the decanter centrifuge industry. More information, plz contact with lin@gnsolidscontrol.co

Solids Control centrifuge for sale with big discount

Leave a reply

GN Solids America have 3 sets of Fixed speed & high speed centrifuge for sale. The centrifuge is fabricated in the end of last year. It is our former design with two electric motors in two end. This centrifuge is working in many oilfield, the performance is good. For the new design, there is better performance on the oil lubrication system and also two motors on one end give more space for operators.

After we issue the promotion information, we have got active inquiry on the centrifuge. Now we have customer from Middle East who will give us orders and down payment within 3 days. This customer is also our old customer who have 2 sets variable speed control panel desander from GN Solids Control. That means, only one set centrifuge is remaining for sale. Pls act quickly if you have real requirements.

GN Solids America will attend ADIPEC in Nov. 2014 and NOG in Feb.2015, which is hosted in Abu Dhabi, UAE and Abuja, Nigeria separately. We will also take some centrifuge to the exhibition. This centrifuge is also for sale with big discount. If you are customer from middle east and close to UAE, pls contact our Middle East Sale Man for quotation. If you are from Nigeria or Ghana Or Gabon, pls contact our Africa Sale man for quotation. After the show close, you can transport the centrifuge away.

GN Solids America as the leading manufacturer of solids control centrifuge and waste management centrifuge can satisfy the requirement from most of the customer. The specified requirement on decanter centrifuge, we can customize for customer. ( Like color, LOGO etc.)

GN Solids Control Attend CIPPE 2014 Shanghai

Leave a reply

GN Solids Control participate on Sixth CIPPE 2014 (from August 26th to August 28th ) held in Shanghai. GN attracts a heap of clients and buyer attention.

Why is GN the second to none in Chinese solids control industry?

GN Solids Control carries a full line of products for the solids control industry. We also offer equipment from shaker screens, shakers, mud cleaners, decanter centrifuge to the complete closed loops system. Our commitment to an unparalleled level of equipment and service has enabled us to enjoy tremendous growth and a leading position in our field. Under the fierce competition, it is our quality units and fast service that we believe makes us number one.

What GN display on the OTC Shanghai

GN Big bowl decanter centrifuge is showed on the OTC. GN big bowl decanter centrifuge is with maximum 484 treating capacity and 22 inch bowl diameter. Typical speed is able to reach 2500RPM and 35:1 rational gearbox. There is no doubt that durable SS316L stainless steel and tungsten carbide alloy of solids discharge gains the public eyes.

Why we choose GN Solids Control?

GN Solids Control implements reduce, reuse and recycle philosophy handle with drilling fluids, combining our solids control units and fast services. We are commitment to responsive fluid control and are able to recycle more drilling fluid than our competitors. Our integrated portfolio of cutting-edge solids control technologies are engineered to optimize drilling performance by reducing fluid losses and costs. GN Solids Control is dedicated to the supply of quality products including, shale shaker, desander, desilter, mud cleaner (mud conditioner). Centrifugal pump and mud agitators. GN also offers new decanter centrifuge and vertical cutting dryer. Proven reliability and continued customer support is demonstrated with worldwide installations to some of the largest company in the world.

Talk with GN Solids Control, you will find more solutions for your drilling fluids.

GN Subsidiary Manufactured Workshop Is Ready

Leave a reply

As a leading manufacturer of solids control industry, GN solids control is meticulously working on the improvement of solids cont units. Keeping challenging ourselves and offer premium equipment is still in our mind. After years and years Unremitting efforts, GN Solids Control units and system are widely recognized by all over the world people and company. The requirement of our units is dramatically increasing. Under the massive demand from our client and potential customer, GN started setting up fourth manufactured workshop last year, and will be ready for operation in the beginning of next year.

GN decanter centrifuge and centrifugal pump will be fabricated in our new workshop. GN decanter centrifuge and centrifugal pump own the top technology and high working performance. GN old workshop is not able to meet with new demand. Therefore, GN promptly make new stride to open new workshop with advanced dynamic balanced device, testing device and CNC lathe and machining center

GN Decanter Centrifuge Achievement

Maximizing barite recovery or looking to get the most out of your “zero-discharge” system, GN field proven decanting centrifuges are a perfect choice. With units installed worldwide, GN centrifuges can be found in almost every harsh environment, including Middle East, Russia, Africa and Brazil. Like all GN products, each centrifuge package is customized to meet your specific needs.

GN Centrifugal Pump

A centrifugal pump is using a rotating impeller to increase the pressure of a fluid. Centrifugal pumps
are commonly used to move liquids through a piping system. The fluid enters the pump impeller along or near to the rotating axis and is accelerated by the impeller, Centrifugal pumps are used for large discharge through smaller heads. GN centrifugal pump is replaceable with Nov Mission pump with treating capacity from 198GPM to 1408GPM

Welcome you to visit our new workshop

The Major Parts of Oil Drilling System

Leave a reply

Once the whole equipment is at drilling site, the staff will set the drilling rig up. There are some major parts of a land oil rig:

Drilling Parts

Hoisting system – used for lifting heavy loads; consists of a mechanical winch with a large steel cable spool, a block-and-tackle pulley and a receiving storage reel for the cable

Swivel (Tong) – large handle that holds the weight of the drill string; allows the string to rotate and makes a pressure-tight seal on the hole

Turntable or rotary table – drives the rotating motion using power from electric motors

Drilling Pipe – consists of drill pipe (connected sections of about 30 feet (10 meters) and drill Collars (larger diameter, heavier pipe that fits around the drill pipe and places weight on the drill bit)

Drill bit(s) – end of the drill that actually cuts up the rock; comes in many shapes and materials (tungsten carbide steel, diamond) that are specialized for various drilling tasks and rock formations

Casing – large-diameter concrete pipe that lines the drill hole, prevents the hole from collapsing, and allows drilling mud to circulate

Blowout preventer – high-pressure valves (located under the land rig or on the sea floor) that seal the high-pressure drill lines and relieve pressure when necessary to prevent a blowout (uncontrolled gush of gas or oil to the surface, often associated with fire)

Circulation system

pumps drilling mud (mixture of water, clay, weighting material and chemicals, used to lift rock cuttings from the drill bit to the surface) under pressure through the kelly, rotary table, drill pipes and drill collars

Pump – sucks mud from the mud pits and pumps it to the drilling apparatus

Pipes and hoses – connects pump to drilling apparatus

Mud-return line – returns mud from the hole

GN shale shaker – sieve large particle and solids from drilling fluids which 100% separate the cutting

GN Mud cleaner- Second step is after the shale shaker, which is including 10 inch desander and 4 inch desilter. Mud cleaner can handle from 350 GPM to 1500 GPM drilling fluids

GN Decanter Centrifuge-Cutting points reach to 2~10 microns, effectively separate the fine partilce

GN Screw Conveyer(Auger) – conveys cuttings from GN Solids Control unit to the reserve pit
reserve pit – collects rock cuttings separated from the mud

GN Mixing and Recycle Tank – where drilling mud is mixed and recycled

GN Jet Mud Mixer – where new mud is mixed and then sent to the mud tank

For drilling site circulation system, you could consult with GN for a better option.

Australia Frequent Mobile Mud Tank System

Leave a reply

Frequent modifications of Horizonal Directional Drilling (HDD) constructing net page demands the drilling gear to mobile and transportable from 1 location to a extra. To attain this point, the drilling mud tank technique could possibly be mounted on a trailer or assembled with hydraulic jack legs. Not also extended ago we’ve got constructed a hydraulic lifting HDD mud cleaning and recycling unit in accordance for the Australian requires. The mud tank is generally lifted by four hydraulic jack legs.

The client calls to acquire a two-tank plan for his project, and amongst tanks equips with two decanter centrifuge for mud material recovery. The centrifuge utilised is GN Solids Control most well-liked model GNLW363G.

Earlier this month, a set of hydraulic jack up mud cleaning unit has been functioning in NSW Australia. You will have the ability to learn about an added mobile unit – trailer mounted mud tank strategy.

Shaker Screen Mesh Size Design and style

Leave a reply

Plain square and rectangular weaves are usually referred to by the amount of wires (or openings) in every single path per linear inch. This really is known as the mesh count. The mesh count is determined by starting at the centre of one wire and counting the number of openings along the Shaker Screen grid towards the next wire centre, one linear inch away. One example is, an 8-mesh screen has eight openings in two directions at right angles to each other. When counting mesh, a magnifying glass scale designed particularly for this objective is helpful.

Use of a single quantity for describing screens implies a square mesh. By way of example ?°20 mesh± usually describes a screen having 20 openings per inch in either direction along the screen grid. Oblong mesh screens are frequently labelled with two numbers. A°60 x 20 mesh?, for instance is normally understood to possess 60 openings in a single path and 20 openings per inch within the perpendicular direction. Referring to a ?°60 x 20 mesh? screen as an ?°oblong 80 mesh is confusing and inaccurate.

The actual separation that a screen is capable of is largely determined by the size of the openings in the screen. The opening size is definitely the distance among wires measured along the screen grid and is expressed in either fractions of an inch or in microns, though it is most usually stated in microns. One particular inch equals 25,400 microns. Preserve in mind, specifying the mesh count does not specify the opening size. That is because each the amount of wires per inch and the size of the wires determines the opening size.
more shaker screen infor: Shaker Screen Arrangement

Mud cleaner plays a essential element

Leave a reply

Mud cleaner plays a essential element inside the drilling liquid strong handle program. Mud cleaner integrate swirl ten inch de sander, 4 inch de silter and bottom shale shaker, which correctly process the drilling fluids immediately after shale shaker. In some methods, mud cleaner procedure large treating capacity, fast speed and occupies smal space l,
Technically, mud cleaner is encouraged for heavier and modest particles contained drilling fluid. Small fine particle might be extracted by the hydrocyclone but not clog within the cone. Shaker screen will approach the fluids in the Apex of hydrocyclone. liquid inlet pressure ought to be maintained towards the extent 0.25~0.4MPa. GN mud cleaner could be the modest because the US Mission pump which effectively feeding the drilling fluid for the de sander cone and de sitler cone.
Our mud cleaning is extensively applied for the oil & gas drilling site, dredge slurry site, horizontal direction drilling, bored plant, tunnel boring, mining industry even the concrete separation. GN also is extensively recognized as leading the way in the solids control industry. Not only single unit shale shaker, mud cleaner, centrifuge and vertical cutting dryer, but also sophisticated complete technique.
Real-time drilling monitoring program for measuring very important values:http://www.drillmudsystem.com/post/87374631824/real-time-drilling-monitoring-program-for-measuring

Dual function unit with double deck shale shaker and mud cleaner : http://drillwastemanagement.com/dual-function-unit-with-double-deck-shale-shaker-and-mud-cleaner/

GN Composite Material Shaker Screens for Sale

Leave a reply

GN Solids America now has composite material frame shaker screen for sale to show our thanks to old and new clients.
GN is specialistnot only in equipments like shale shakers and centrifuges, but additionally in shaker screen. Together with thebeneficial feedbacks from our shale shaker finishusers, GN gathered much morefacts and ideas, with theseinformation, GN in no way stops its step for enhancing the good quality and prolong the service life of shaker screens. Comparing with steel frame pretension screens, composite material screens are improved sealed and can serve a longer time.
GN composite material shaker screen are developed for GNZS594 series shale shakers and mud cleaners. Screen region of GNZS594 is usuallyup to2.73 square meters by utilizing4 panels of such screen.
Under are detailed parameters of this screen:
Mesh: API 20-API 400
Dimension: 1165(L) 585(W) 40(H)mm
Weight: 12kg
Layer of mesh cloth: two or three layers per API number
Screen mesh cloth material: SS316
Screen frame material: Composite material
Besides above mentioned shaker screens, GN Solids Managetends to make other models of screens of premium quality and reasonableprice tag. Lots ofrenowned shale shaker userssupply from GN the replacement shaker screens for a lot more cost-effective.
GN Solids Americagenerally have promotion for shaker screen. Welcome to add me into your contact for updated for sale facts.

shale shaker screen which is the best one?

Operational Recommendations of Shaker Screen