Monthly Archives: March 2015

GN Drilling Waste Management Systems

GN Drilling Waste Management Systems
GN Solids Control has many experience engineers in waste management area. In order to meet the demands of environment protection and make money from the waste oil, using GN drilling waste management systems would be one cost effective method.
GN drilling waste management systems is a pretty standard system mainly including one GN cuttings dryer and one decanter centrifuge, two positive pumps (one for cleaning and flushing the cuttings dryer when the work is finished, the other one is used for feeding mud into the decanter centrifuge), skid and tank as well as some other auxiliary equipments such as ladders, walkways, guiderails and lights etc.
In order to operate GN drilling waste management systems conveniently, GN designers take the working conditions into consideration. The whole systems are pretty compact, while the operators have large room for work.
GN cutting dryer is quite effective for OBM, WBM or SBM treating. When using GN dryer, on one hand you can separate the solids out from the waste mud, on the other hand you can reclaim some precious oil which can be used for further treatment and sell to make profit. From this point, treat the waste oil can reach the aim of protecting environment and make money.
Solids come out from the waste mud contain a little bit oil, according to the discharge standard, these solids can be discharged directly without any further treatment due to the oil is less than 5 percent.
As to the WBM treating, GN dryer also can perform excellently. Solids usually contain less than 10% water. These solids can be transported to other places after 2 or 3 days nature dry.
Fluids come out from cuttings dryer can be sent to decanter centrifuge for further separation. All the solids larger than 2 or 3 microns can be separated out.
GN drilling waste management system can also working in harsh environment which is very cold. Last December, some sets of GN drilling waste management systems are using in Russia, where the temperature is minus 40 ℃.
cuttings_drying_system_before_shipping
GN Solids Control has many experience engineers in waste management area. In order to meet the demands of environment protection and make money from the waste oil, using GN drilling waste management systems would be one cost effective method.
GN drilling waste management systems is a pretty standard system mainly including one GN cuttings dryer and one decanter centrifuge, two positive pumps (one for cleaning and flushing the cuttings dryer when the work is finished, the other one is used for feeding mud into the decanter centrifuge), skid and tank as well as some other auxiliary equipments such as ladders, walkways, guiderails and lights etc.
In order to operate GN drilling waste management systems conveniently, GN designers take the working conditions into consideration. The whole systems are pretty compact, while the operators have large room for work.
GN cutting dryer is quite effective for OBM, WBM or SBM treating. When using GN dryer, on one hand you can separate the solids out from the waste mud, on the other hand you can reclaim some precious oil which can be used for further treatment and sell to make profit. From this point, treat the waste oil can reach the aim of protecting environment and make money.
Solids come out from the waste mud contain a little bit oil, according to the discharge standard, these solids can be discharged directly without any further treatment due to the oil is less than 5 percent.
As to the WBM treating, GN dryer also can perform excellently. Solids usually contain less than 10% water. These solids can be transported to other places after 2 or 3 days nature dry.
Fluids come out from cuttings dryer can be sent to decanter centrifuge for further separation. All the solids larger than 2 or 3 microns can be separated out.
GN drilling waste management system can also working in harsh environment which is very cold. Last December, some sets of GN drilling waste management systems are using in Russia, where the temperature is minus 40 ℃.

GN Dredging System Mud Tank

GN Dredging System Mud Tank

Every year, GN Solids Control provides over hundreds of systems to solids control or mud recycling system. And GN is manufacturing about 350 to 400 sets shale shakers, 250 to 300 sets decanter centrifuges and 60 sets to 100 sets cuttings dryers.
As the fast development of GN Solids Control Co. and GN Solids America LLC, more and more companies are coming to GN for their mud separation solutions.

GN also providing various tanks to customers who are working in oil and gas, HDD, Dredging, CBM or TBM areas etc. During the past several months, GN got many inquiries on mud tanks. Some are pretty small one such as hundred bbl, while some are large mud plant such as 10,000 bbl.

GN_Dredging_Separation_System

For different areas, GN has customized solution for every client. Let’s take the dredging slurry mud system as an example. In order to better service the needs of dredging separation demands, GN has designed V type tank to satisfy their demands on clean the mud in the tank conveniently. Usually, there will be some mud fall on the bottom of the mud tank, and the mud can be cleaned out from the hole on both sides of the tank. Actually, this is not a easy job to do, many mud will be left inside no matter how hard you try to get them out.

But if you’re using GN V type tanks, tough thing will be just a cup of tea. GN has assembled one screw conveyor on the bottom of the mud tank, all the mud that fall off on the bottom will be conveyed by GN screw conveyor, so it will be separated thoroughly. When the separation work is finished, you can stop all the shale shakers on the bottom and start the screw conveyor to get the mud out.

GN also designed one square mud tank next to the V tank. The square mud tank can help to enlarge the capacity of this dredging system